The main difference is that MTP was designed for superior mechanical and optical performance over MPO.By Steve Somers, Vice President of Engineering The two connector types are backwards compatible and work with all MTP/MPO cassettes and patch panels. MPO is the generic name for the connector type while MTP is a registered trademark name and design from UsConnec. Q: Are MTP and MPO cables the same thing?Ī: MTP and MPO cables are essentially the same thing. The end face of the APC connector fiber is polished at an 8 degree angle which prevents back reflections that degrade the performance of your system. APC connectors have a return loss of more than 60dB. The APC connectors were made to decrease insertion loss and increase the return loss even more. UPC connectors have a return loss of more than 50dBs. UPC connectors are finely polished on the ends of the fibers in order to decrease insertion loss and increase return loss (the higher the return loss the better the connection). Q: What is the difference between UPC fiber connectors and APC fiber connectors?Ī: UPC stands for Ultra Physical Contact and APC stands for Angled Physical Contact. Q: What is the difference between 50/125 and 62.5/125 fiber?Ī: 50/125 can be run further with less loss than 62.5/125 fiber. In the case of extreme bending of the optical fiber, the optical signal leaked to the outside of the core due to bending is retained, and the loss of the optical fiber is reduced. Ultra-high bending performance, overcome corner turning, improve cable utilization, ensure the normal and stable operation of communications. It has good thermal stability, high hardness and environmental adaptability. Optimum insertion loss and return loss ensure stable signal transmission and network security. Optical Fiber Connector, Length, Color, Optical Fiber Grade, Specification, Material, Packaging, etc.Īll jumpers are strictly tested before leaving the factory to ensure that the end surface is spotless, insertion loss and echo loss are in line with international telecommunications standards.Įconomical and Efficient Bending Insensitive Optical Fiber JumpĬeramic plug duplex connector design, suitable for high-speed wiring network transmission and in line with EIA/TIA 604-2 industry standards. Optical fiber jumper is used to connect data center, CATV, optical fiber test equipment, LAN, telecommunication network, FTTx, communication room,optical fiber communication system, defense warfare preparation, etc. The commonly used LC jumpers are used to connect optical fiber and optical modules, so they are usually LC-SC or lc-fc, and most of them are used in pairs, and there are few single LC jumpers. LC connector is used to connect SFP fiber module and is made of convenient operation modular jack (RJ) latch mechanism. LC connector is similar to SC connector, but smaller than SC connector. Due to the need to rotate, the installation is inconvenient, so the installation time is a little longer. The FC connector is similar to st connector, and its shape is round, but the FC connector has thread inside and is connected with FC coupler through rotation. Because the connector needs to rotate half a circle after being inserted and fixed by bayonet, it is easy to break. The shell of ST connector is round with bayonet, which is connected with ST coupler and needs to rotate about 90 ° when using. However, the connector is easy to fall out when used for a long time. It is made of engineering plastics, resistant to high temperature and not easy to oxidize. It is directly inserted and inserted without rotation. The shell of the SC connector is rectangular, which is connected with the SC coupler. Various optical fiber jumpers (SC, FC, LC, ST) Cable materiaal: PVC, LSZH "SM = Enkele Modus MM = Multi Modus SX = Simplex DX = Duplex " Length: 1,2, 3,5, 10 meter of customized length Ħ. SM UPC ≥ 50dB(min) SM APC ≥ 60dB(min) MM PC ≥ 35dB(min)ġ.Connector Type: LC, SC, FC, ST, FC, Mu MTRJ, MPO, E2000 2. SM: Yellow/Blue/White OM1&OM2: Orange OM3:Aqua Compliant with Telcodia GR-326-Core, JIS-5973,TIA/EIA 604.Low Insertion Loss and high Return Loss.G.657.A1 OS2 single mode optical fiber is selected for its single mode jumper, which meets the ROHS standard.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |